% FGE italic 10 point % this is derived from cmti10.mf by Knuth % J.J.Green 2006 if unknown cmbase: input cmbase fi if unknown fgebase: input fgebase fi font_identifier := "FGEIT"; font_size 10pt#; u# := 18.4/36pt#; % unit width width_adj# := 0pt#; % width adjustment for certain characters serif_fit# := 0pt#; % extra sidebar near lowercase serifs cap_serif_fit# := 5/36pt#; % extra sidebar near uppercase serifs letter_fit# := 9.2/36pt#; % extra space added to all sidebars body_height# := 270/36pt#; % height of tallest characters asc_height# := 250/36pt#; % height of lowercase ascenders cap_height# := 246/36pt#; % height of caps fig_height# := 232/36pt#; % height of numerals x_height# := 155/36pt#; % height of lowercase without ascenders math_axis# := 90/36pt#; % axis of symmetry for math symbols bar_height# := 87/36pt#; % height of crossbar in lowercase e comma_depth# := 70/36pt#; % depth of comma below baseline desc_depth# := 70/36pt#; % depth of lowercase descenders crisp# := 8/36pt#; % diameter of serif corners tiny# := 8/36pt#; % diameter of rounded corners fine# := 7/36pt#; % diameter of sharply rounded corners thin_join# := 7/36pt#; % width of extrafine details hair# := 11/36pt#; % lowercase hairline breadth stem# := 23/36pt#; % lowercase stem breadth curve# := 28/36pt#; % lowercase curve breadth ess# := 27/36pt#; % breadth in middle of lowercase s flare# := 29/36pt#; % diameter of bulbs or breadth of terminals dot_size# := 38/36pt#; % diameter of dots cap_hair# := 11/36pt#; % uppercase hairline breadth cap_stem# := 29/36pt#; % uppercase stem breadth cap_curve# := 34/36pt#; % uppercase curve breadth cap_ess# := 31/36pt#; % breadth in middle of uppercase s rule_thickness# := .4pt#; % thickness of lines in math symbols dish# := 1/36pt#; % amount erased at top or bottom of serifs bracket# := 20/36pt#; % vertical distance from serif base to tangent jut# := 30/36pt#; % protrusion of lowercase serifs cap_jut# := 34/36pt#; % protrusion of uppercase serifs beak_jut# := 9/36pt#; % horizontal protrusion of beak serifs beak# := 70/36pt#; % vertical protrusion of beak serifs vair# := 8/36pt#; % vertical diameter of hairlines notch_cut# := 10pt#; % maximum breadth above or below notches bar# := 11/36pt#; % lowercase bar thickness slab# := 11/36pt#; % serif and arm thickness cap_bar# := 11/36pt#; % uppercase bar thickness cap_band# := 11/36pt#; % uppercase thickness above/below lobes cap_notch_cut# := 10pt#; % max breadth above/below uppercase notches serif_drop# := 4/36pt#; % vertical drop of sloped serifs stem_corr# := 1/36pt#; % for small refinements of stem breadth vair_corr# := 1/36pt#; % for small refinements of hairline height apex_corr# := 0pt#; % extra width at diagonal junctions o# := 8/36pt#; % amount of overshoot for curves apex_o# := 8/36pt#; % amount of overshoot for diagonal junctions slant := .25; % tilt ratio $(\Delta x/\Delta y)$ fudge := 1; % factor applied to weights of heavy characters math_spread := 0; % extra openness of math symbols superness := 1/sqrt2; % parameter for superellipses superpull := 1/6; % extra openness inside bowls beak_darkness := 11/30; % fraction of triangle inside beak serifs ligs := 2; % level of ligatures to be included square_dots := false; % should dots be square? hefty := false; % should we try hard not to be overweight? serifs := true; % should serifs and bulbs be attached? monospace := false; % should all characters have the same width? variant_g := true; % should an italic-style g be used? low_asterisk := false; % should the asterisk be centered at the axis? math_fitting := true; % should math-mode spacing be used? % switch to the driver file generate fgeit